UR0250 Methods |
The UR0250 type exposes the following members.
Methods| Name | Description | |
|---|---|---|
 | Connect |
Connects to device using specified port name and settings.
(Inherited from UHF.) |
| ControlBuzzer |
Make reader buzzer to sound a specified beep pattern.
|
| DirectIoMultiAck |
Used by manufacture only.
(Inherited from UHF.) |
| Disconnect |
Close connection.
(Inherited from UHF.) |
| GetAllSettings |
Gets all UR0250 Settings.
|
| GetBleMacAddress |
Gets the reader Bluetooth MAC address.
|
| GetBleRomVersion |
Gets the firmware version running on the BLE module.
|
| GetCommandTriggerState |
Gets the state of command trigger.
|
| GetFirmwareVersion |
Gets the firmware version of the reader.
(Inherited from UHF.) |
| GetInventoryActiveMode |
Gets the operation mode of inventory a tag.
|
| GetInventoryRoundInterval |
Gets the time interval between each inventory round.
|
| GetIOState |
Gets the state of all digital input/output pin.
|
| GetIpAddress |
Gets the reader local IP address.
|
| GetLinkFrequency |
Gets the tag's backscatter link frequency.
|
| GetQValue |
Gets the starting Q value for the number of slots in the round.
|
| GetRfPower |
Gets the RF Power strength.
|
| GetRfSensitivity |
Gets the RF input sensitivity level.
|
| GetRxDecode |
Gets the RF data encoding(Baseband FM0 or Miller-modulated subcarrier).
|
| GetSessionAndTarget |
Gets the session flag and target used for inventory round.
|
| GetTagRemovedThreshold |
Gets the time period that the reader doesn't detect to determine a tag is presented.
|
| GetWiFiApDetailList |
Gets a list of Wi-Fi access point SSID and RSSI.
|
| GetWiFiApList |
Gets a list of Wi-Fi access point names.
|
| GetWiFiMacAddress |
Gets the reader Wi-Fi MAC address.
|
| InventoryTags | (Inherited from UHF.) |
| KillTag(String) |
Permanently disable a Tag
|
| KillTag(String, String) |
Permanently disable a Tag
|
| LockTag(DictionaryMemoryBank, LockAction) |
Lock or unlock specified memory.
|
| LockTag(String, DictionaryMemoryBank, LockAction) |
Lock or unlock specified memory.
|
| ReadTag(String, MemoryBank, Int32, Int32) |
Reads tag raw data from given memory bank.
|
| ReadTag(String, String, MemoryBank, Int32, Int32) |
Reads raw data from tag with specified EPC.
|
| SetAllSettings |
Sets all UR0250 Settings.
|
| SetCommandTriggerState |
Sets the state of command trigger.
|
| SetInventoryActiveMode |
Sets the operation mode of inventory a tag.
|
| SetInventoryRoundInterval |
Sets the time interval between each inventory round. The value is ranging from 0 to 254.
|
| SetIOState |
Sets the digital input/output pin specified HIGH or LOW.
|
| SetLinkFrequency |
Sets the tag's backscatter link frequency. May affect data transmission speed.
|
| SetQValue |
Sets the starting Q value for the number of slots in the round.
|
| SetRfPower |
Sets the RF Power strength. The value is ranging from 1 to 27.
|
| SetRfSensitivity |
Sets the RF input sensitivity level.
|
| SetRxDecode |
Sets the RF data encoding(Baseband FM0 or Miller-modulated subcarrier).
|
| SetSessionAndTarget |
Sets the session flag and target used for inventory round.
|
| SetTagRemovedThreshold |
Sets to determine a tag is removed after reader doesn't detect in a given inventory rounds. The value is ranging from 0 to 254.
|
| StartInventory |
Starts the process of tag inventory using specified trigger source.
(Inherited from UHF.) |
| StopInventory |
Stops the process of tag inventory.
(Inherited from UHF.) |
| WriteEPC(String, Byte) |
Writes EPC into tag.
Note this API will automatically calculate and write the Gen2 PC based on the EPC length.
UMI, XI, T, bits will set to 0.
AFI or Attribute byte will set to 0.
If you want to write EPC with specified T, AFI or Attribute, call WriteTag(String, MemoryBank, Int32, Byte) instead.
|
| WriteEPC(String, String, Byte) |
Writes EPC into tag with specified EPC.
Note this API will automatically calculate and write the Gen2 PC based on the EPC length.
UMI, XI, T, bits will set to 0.
AFI or Attribute byte will set to 0.
If you want to write EPC with specified T, AFI or Attribute, call WriteTag(String, String, MemoryBank, Int32, Byte) instead.
|
| WriteTag(String, MemoryBank, Int32, Byte) |
Writes raw data into tag.
|
| WriteTag(String, String, MemoryBank, Int32, Byte) |
Writes raw data into tag with specified EPC.
|
| WriteTagEx(String, SGTIN_198) |
Encode GTIN barcode to SGTIN-198 and write into tag's EPC bank.
|
| WriteTagEx(String, SGTIN_96) |
Encode GTIN barcode to SGTIN-96 format and write into tag's EPC bank.
|
| WriteTagEx(String, SGTIN_96_EAS) |
Encode GTIN barcode to SGTIN-96 + EAS format (GIGA-TMS) and write into tag's EPC bank.
|
| WriteTagEx(String, UDCTagData) |
Encode GTIN barcode to UDC format (GIGA-TMS) and write into tag's EPC bank.
|
| WriteTagEx(String, String, SGTIN_198) |
Encode GTIN barcode to SGTIN-198 and write into specified tag's EPC bank.
|
| WriteTagEx(String, String, SGTIN_96) |
Encode GTIN barcode to SGTIN-96 format and write into specified tag's EPC bank.
|
| WriteTagEx(String, String, SGTIN_96_EAS) |
Encode GTIN barcode to SGTIN-96 + EAS format (GIGA-TMS) and write into specified tag's EPC bank.
|
| WriteTagEx(String, String, UDCTagData) |
Encode GTIN barcode to UDC format (GIGA-TMS) and write into specified tag's EPC bank.
|
See Also